PLEASE VISIT OUR SOLAR PAGE ..CLICK ON TOP "SOLAR"

Sunday, June 26, 2011

വയര്‍ ലെസ്സ് ഡോര്‍ ബെല്‍


വെറും 150 രൂപയ്ക്കു ഇലക് ട്രോണിക്സ് കടകളില്‍ ലഭിക്കുന്ന വയര്‍ ലെസ്സ് റിമോട്ട് കണ്‍ ട്രോളരിന്റെ സര്‍ക്യൂട്ടാണിതു .
ഇത് വാങി പലവിധ മാ‍റ്റങള്‍ വരുത്തിയാല്‍  റിമോട്ട് gate opener ആക്കി മാറ്റാം
സ്പീക്കര്‍ കൊടുത്തിരിക്കുന്ന സ്ടാനത്ത് ഒരു റിലെ കണക്റ്റു ചെയ്താല്‍ മതി

Transistor Type: Collector current: Max frequency
8050 NPN 1.5A 100MHz
8550 PNP 1.5A 200MHz
9014 NPN 150mA 150MHz
9018 NPN 50mA 700MHz

The first thing you will notice is the clever circuitry. Some of the design goes against everything we have learnt in electronics.
That's why we have to study other people's designs and realise "the more you know, the more you realise you don't know."
The oscillator circuit is very interesting, but first we will look at the RF oscillator.
The doorbell operates on the 303MHz band and the 30 metre range (100ft) is obtained without the use of an antenna! The circuit is actually radiating from the printed track of the tank circuit. The Tank Circuit is a single-turn coil and a small capacitor (5p & 4p in parallel).

In this project we show how to add a small antenna to the circuit to get double the range - plus two other improvements to increase the range.
Some of the improvements will load the  circuit and alter the frequency at which it operates. Others can be done without any effect on the circuit.
Fortunately, the transmitting stage is what we call "tight" and is not affected by surrounding "stray capacitance."
Normally, this stray capacitance is a persons hand or body, touching or coming near the transmitting (output) stage and altering the frequency.
The circuit has been kept near the power rails by the use of a choke in the positive rail. The positive rail is then reflected to the negative rail via the battery.
This feature helps us when we want to add an antenna.
A 7cm length of tinned copper wire is connected to the collector of the transistor and bent around the board so that everything can be put back into the case.
When the project was tested inside the authors house, the range was increased to double.
When the transmitter was taken outside, the range was over 60 metres (200ft) and the full range could not be tested as the sound from the doorbell was too faint to be heard! 

We can learn so much from a product that is already on the market.
Firstly, you know it works, it is reliable and you know what can be built for RS 200
Secondly, you know what type of components can be purchased cheaply and what to expect from them.
In this case the transmitting transistor has the highest gain - so they have taken a special effort to get a good quality transistor.   
Now, let's look at the transmitter circuit:

ട്രാ‍ന്‍സ്മിറ്റര്‍ സര്‍ക്യൂട്ട്
The transmitter circuit is made up of two building blocks - the 303MHz RF oscillator and the 32kHz crystal controlled oscillator.

The 303MHz oscillator consists of a self-oscillating circuit made up of the coil on the PC board and a 9p (9 puff) capacitor (actually 4p and 5p in parallel).
The circuit starts-up by the transistor producing noise. This rising-and-falling signal on the collector is passed to the parallel tuned circuit (the tank circuit) and the base sees a very smooth sinewave at a frequency of 303MHz.
This sinewave is then amplified by the transistor and this is how the 303MHz frequency is generated.
Now we come to the purpose of the 15microhenry choke on the tank circuit.
When the circuit oscillates, it takes a larger and small amount of current.
This current passes through the choke and the turns produce a back-emf or back voltage that fights against the flow (change) in current. The end effect is a voltage created at the point where the choke is connected to the track-work on the board. This effectively allows the track work to produce a waveform and since the frequency of this wave is very high, a percentage of the energy is radiated into the air as electromagnetic energy.
The choke allows the track-work to effectively rise and fall while providing a very low resistance path for the flow of current during certain parts of the cycle.

The second building block is the crystal oscillator.
This is made up of a two-stage DC coupled amplifier with feedback via the 2n2 and crystal.
If the crystal is removed, the oscillator is seen as producing very narrow spikes with a frequency determined by the 2n2, as shown in the diagram below:

When the crystal is added, the frequency increases (because the effect of the 2n2 and crystal in series creates a lower capacitance than 2n2) and as it rises, the amplitude of the feedback signal increases until it reaches a maximum at the resonant frequency of the crystal. The crystal exhibits the lowest impedance (the highest capacitance) at the resonant frequency. This is how the circuit stabilizes at the frequency of the crystal.
When the device is turned on, the 150k on the base of the second transistor turns the transistor on.
The third transistor has 0.65v on the collector and the base also receives very close to 0.65v, via the 220k resistor.
The third transistor is not fully turned on and it produces a small amount of noise.  This noise is passed to the second transistor and appears on the collector. The collector passes this noise to the base of the third transistor and the noise very rapidly increases to a maximum.
It comes to a point where the waveform above is generated and the reason why the spikes are so narrow is easy to explain.
When the middle transistor changes from an OFF state to an ON state, the capacitor will be partially charged and the voltage on the end connected to the base of the third transistor will drop about 6v and put a negative voltage on the base of the third transistor. This will keep it off and the middle transistor will be kept ON via the 150k base-resistor.
The capacitor will gradually charge in the opposite direction via the 220k and 150k and when the base of the third transistor sees about 0.6v, it begins to turn ON.
This causes the middle transistor to turn OFF and the collector voltage rises. This causes the capacitor to charge and create a current-flow in the base of the third transistor. Both transistors are now turned ON and the capacitor charges very quickly via the 12k and base-emitter junction of the third transistor. This creates the very narrow high-period in the waveform.

When the push button is pressed, the circuit produces a 303MHz carrier with a 32kHz tone.
The receiver detects the 32kHz and turns on a SOUND chip.
റിസീവര്‍ സര്‍ക്യൂട്ട്
The receiver circuit consists of a number of stages and we will go through each one separately.

The first stage is actually a 303MHz oscillator that is operating all the time.
It produces a clean 303MHz signal and this frequency is too high to be detected or processed by the 4069 chip, as the chip will only operate to about 1MHz.
The theory behind using this type of stage is quite simple.
It is easier to "upset" or modify a stage that is already oscillating, rather than get a non-oscillating stage to begin oscillating.
There are all sorts of electromagnetic radiation at 300MHz and the 2-turn coil picks up all this noise.
The 303MHz oscillator is firstly set into operation by the noise produced by the transistor and this is passed to the tank circuit made up of the 2-turn coil and 2p capacitor as a parallel tuned circuit. The transistor keeps amplifying this until it gets to a stabilized point where the collector is producing "hash"  (junk) of about 300mV.
When the transmitter is activated, the receiver circuit will detect a signal as small as a few micro-volts and the 32kHz signal will be included with all the other noise. 
There is a little bit more behind this receiving stage, than first meets the eye.
The stage is actually a transmitter, but we will still call it the receiver circuit. Yes, it is a very weak transmitter and it fills the surrounding with a clean 303MHz signal. When the 303MHz signal from the transmitter enters this space, the signals interfere with one another and the receiver takes more and less current as it tries to maintain the signal strength. When the 32kHz signal is present, the receiver takes a varying current that corresponds to the 32kHz signal and this is how the receiver circuit produces the waveform to correspond to the 32KHz.  
A low-impedance path to the 0v rail is provided for the emitter by using a 82uH choke and a 2n2 capacitor across a 560R resistor. This low impedance path is needed so that the transistor has a high gain.
The circuit is put into very delicate oscillation by using a 1k5 from the positive rail.
It operates from 3v and the current taken by this stage is less than 1mA.

THE BRASS TUNING-SLUG
The coil in the tank circuit is tuned via a brass screw (or slug or core). This is alters the frequency at which the circuit operates, when it is turned via a small screwdriver.
At 303MHz, you cannot use a ferrite core as it will completely absorb the magnetic radiation produced by the coil and prevent the circuit operating.
Another choice is air. If you use an air cored coil, you can use a trimmer capacitor to adjust the frequency. A cheaper approach is to use a brass core. Brass has a permeability very close to air (
µ is the permeability of free space) and it has very little effect on concentrating the magnetic lines of flux or moving them apart. Materials that cause the lines of flux to move farther apart, resulting in a decrease in magnetic flux density compared with a vacuum, are called diamagnetic. Materials that concentrate magnetic flux by a factor of more than one but less than or equal to ten are called paramagnetic; materials that concentrate the flux by a factor of more than ten are called ferromagnetic.
However, at very high frequencies, such as 303MHz, the magnetic flux causes eddy currents to flow in the brass and this decreases the available flux so that inserting a brass core causes the frequency to drop.
This is how the receiver is tuned to exactly the same frequency as the transmitter.   
The most critical capacitor in the receiver is the 2p. This sets the frequency. The 4p is merely a feedback capacitor.
The 2n2 and 1n are called "pass" capacitors and allow high frequency signals to pass through them.   The 1n actually keeps the positive and negative rails rigid while the 2n2 prevents the emitter moving up and down when amplifying the 303MHz signal.
The signal on the collector passes to the first input of the chip via a 5k6 resistor and 1n (pass capacitor). A lot of the high frequency component is removed with the 1n capacitor connected to the 0v rail.


The first inverter has a 1M connected between the output and input to set it to mid rail so it becomes a high-gain amplifier.
The second and third inverters also amplify the signal and on pin 6 we have a signal greater than 0.6v containing a lot of noise and an identifiable 32kHz waveform.
The 32kHz crystal only allows the 32kHz signal to pass and the base of the transistor sees a very clean signal. Any other frequencies will not appear on the base of the transistor. The 32kHz is further amplified with two more stages and appears at pin 10 of the chip.
It is then passed to a diode pump that charges a 47u electrolytic.
Normally, this electrolytic is uncharged and pin 8 is HIGH. The PNP transistor is not turned on and the sound chip is silent.
But when the electrolytic charges, the transistor turns on and the sound chip operates.

കൂടുതല്‍ വിവരങള്‍
One of the main reasons for presenting this project is to show how to get the best range from a transmitter.
Normally you need very expensive equipment to help you, but a very clever alternative is to use our method.
All you have to do is place the receiver about 15 metres from the transmitter and in a very poor reception area.
The aim is to get the receiver to be at the extreme end of the range so that if you move the transmitter away by as little as a metre, the receiver will not detect the signal.
Now the receiver is a very sensitive RF indicator. By moving  the transmitter to different places, the receiver should not detect the signal.
You are now ready to add an antenna to the transmitter and determine its effectiveness.
We have already mentioned the transmitter circuit is classified as "tight" and adding an antenna should not shift the frequency.

ADDING AN ANTENNA
The 7cm antenna is added to the point where the choke touches the PC coil on the board.

Adding the 7cm antenna

This point is highly active but it does not interfere with the operation of the circuit, when the antenna is connected. 
Bend the wire around the edge of the board and about 0.5cm above it and test the transmitter. You should get an increase in the range, up to double.
If the range does not increase appreciably, the receiver may not be tuned exactly to the transmitter. To do this, adjust the brass screw in the tank circuit of the receiver.
Before making any adjustment, make sure you know the original position by noting the alignment of the slot.
Only turn the screw about 15° in either direction and take a "field test." If the range reduces, you know the screw has been turned in the wrong direction.
RANGE കൂട്ടാം
 

Another thing that will increase the output of the transmitter involves rewiring the LED.
At the moment the LED is in series with the positive rail of the transmitter.
This effectively drops about 1.7v and the circuit only gets 7.3v from a fresh battery.
By connecting the LED between the positive and 0v rail, with a 470R load resistor, the transmitting section will see 9v and this will increase the range.
One more thing that will increase the output is to add a 220R across the 220R emitter resistor of the transmitter transistor.
This increased the range in our prototype, but the frequency-adjusting screw on the receiver had to be turned about 15° clockwise to compensate for the slight change in frequency.


PARTS LIST
Wireless Doorbell
ഈ സര്‍ക്യൂട്ടിന്റെ പ്രിന്റെഡ് സര്‍ക്യൂട്ട് ബോര്‍ഡ്

PCB HOME ERNAKULAM എന്ന സ്താപനത്തില്‍ നിന്നും ലഭിക്കും
PHONE   9633271753
1 - 220R resistor
1 - 470R
1 - 7cm tinned copper wire

If you want to build this project using your own components, but do not have the 32kHz crystals, here is a modification that does not need them:
The only components you will have to know how to make are the coils. The size, shape and wire diameter are important as the frequency is very high and the coil must be identical to those in the doorbell products we bought for this article.

mobile invertor,ഇന്‍ വെര്‍ട്ടര്‍

Mobile Inverter 300VA[1]

LED emergency light

ELECTRONICS CIRCUIT

battery saver,ബാറ്ററി സേവര്‍

BATTERY SAVER

electric bike,ഇലക് ട്രിക് ബൈക്ക്

ELECTRIC BYKE

റസിസ് റ്റന്‍സ് കളര്‍ കോഡുകള്‍ ,resistonce colour codes

Colour Codes Centre Spred

mobile secrets,മൊബൈല്‍ സീക്രട്ട്സ്

Layout Pages Final

മലയാളം ഇലക്ട്രോണിക് സ് മാസിക ,malayalam electronics magazine old


December Matter

Friday, June 24, 2011

ടെലിവിഷന്‍ സര്‍വീസ് കോഡുകള്‍

കൂടുതലായി പ്രചാരത്തിലുള്ള ടെലിവിഷന്‍ മൊഡലുകളില്‍ ചിലവയുടെ സര്‍വ്വീസ് കോഡുകള്‍

SONY / LG / SAMSUNG / VIDEOCON / SANSUI / PHILIPS / TCL

SONY Colour Television Receiver

Models:G-Series,J-Series,KV-G21M1,KV-G14F2RS,KV-2197M3(RM-870),KV-G14M1,KV-G14MD1,KV-G14P1,KV-G14P1,KV-G14P11,KV-G14Q1,KV-G14S1(RM-870),KV-J21MF1,KV-J21MH1,KV-J21MN11(RM-870),KV-2168MT,KV-2169MNT(RM-870),KV-XF29M35,KV-XF29M63,KV-XF29M93,KV-XF25M21,KV-XF25M63,KV-XF25M93 (RM-945).KV-XA21M80,KV-XA21M83.KV-XA21M50,KV-XA21M61,KV-XA21M60(RM-952),KV-XF25M81,KV-XF25M80(RM954),KV-F29MF1,KV-F29MH11,KV-F29MH31,KV-F29MN11,KV-F29MN31(RM-857),(RM-858)
For entering into service mode:
· Press the remote control key in the following sequence
              STANDBYðDISPLAYð5ðVOL+ðPOWER
· To raise/lower service item no: press numeric buttons “1” or “4”
· To raise/lower data value: press: “ MUTING” Button on handset
· To execute writing in memory; press “0” on handset
· To cancel service mode ; turn the TV into standby by pressing “POWER” button on the handset, and then again switch on the TV by pressing the same button                    
Chassis:AE2,AE-2B,AP-2
Models: KV-E5231,KV-E2931,KV-E3431,KV-E2551A/B/E/K,KV-S29JN1/MN1/SN1,KV-S34/JN1/MN1/SN1/,KV-B2911,KR-S4613
For entering into Service Mode:
· Turn on the main power switch of the set while pressing any two buttons on the front panel. “TT” will appear on the upper right corner of the screen. Press the “MENU” button on the remote control handset. In menu select “DEMO” and press “OK” Select DEVICE corresponding to the adjustment you need.
· To store; “OK”
· To exit: turn off the set.
Chassis: AE-2
Models: KV-B2911/A/D/B/K,KV-B2913E
For entering service mode:
· Turn on the main power switch of the set while pressing any two buttons on the front panel. “VOL” will appear on the upper right corner on the screen. Press the “MENU” button on the remote control handset.
Chassis:BE-4
Models:KV-2170,KV-2180,KV-2540
For entering into service mode:
· Press remote control keys in the following sequence
· ?ð5ðVOL+ðTVðMENU
· To exit: 00
Chassis:VE-3V,BE-3B
Models:KV-C2171K,KV-C2171K,KV-C2171KR,KV-X2501K,KV-X2581K,KV-X2581KR,KV-M2540K,KV-M2541K,KV-X2901K,KV-X2981K,KV-X2981KR,KV-M1440,KV-M2170,KV-M2171,KV-M2181,KV-M2101,KV-24WS1A/B/D/E/K/RU(RM-837)
Processor:CXP85340A-116Q/117Q
For entering into Service Mode:
· Press the remote control keys in the following sequence
            DISPLAY ON SCREENð5ðVOL+ðTV
· “TT” will appear at upper top corner.
Chassis:G1
Models: KV-S29RN1,KV-S34RN1
For entering into Service Mode:
· Set the TV in on duty mode. Press from the board following button sequence
            DISPLAYð5ðVOL+ðPOWER
Chassis:AE-2F
Models: KV-S2941A/B/D/K,KV-2943E (RM-831)
For entering into service mode:
· Twice press button “VKL” on board. In a right top corner “TT” will appear then press button “MENU”
Chassis: BE-3D,BE-4
Models:KV-24WS1A/B/D/E/K/R/U (RM-862)
Processor:MSP3410B-PS-F7-T,MSP3410C-PS-C6-T
KV-2181KR,KV-M2540,KV-29X1A/B/D/E/K/L/R/U
For entering into Service Mode:
· Set the TV in on duty mode. Press from the board following button sequence
            ON SCREEN DISPLAYð5ðVOL+ðTV
LG Colour Television Receiver
Models:SAMPOORNA,RF-14A80K ADKBBIN,RF-14/20/21CA30K,RF-14/20/21CA30KE, RF-20/21CB30F,RF-20/21CB30VE,RF-21FA20KE,CF-14D79K,CF14D79KE,CF20/21D79K,CF20/21F69K,CF-20/21S12KE,CF-20/21D331KE,CF-20/21S42KS
All Latest Models
For entering service mode:
· Simultaneously press “OK” button on remote handset and on the front panel of television receiver for 6 to 8 seconds.
· Controls: YELLOW button (Q-VIEW button)
· Accessing parameters: Program Up/Dn buttons
· Changing data value: Volume Up/Dn buttons
· To exit: Switch of the set
SAMSUNG Colour Television Receiver
Models: CB-14EV,CB-14E5,CB-20E5,CB-20F4
All Latest Models
For entering into service Mode:
· Press the remote control keys in the following sequence
            POWERðDISPLAYðMENUðMUTEðPOWER
· Controls : CH/P Up/Dn keys
· Changing data value: Volume +/- keys
· To exit Switch off the set.
VIDEOCON Challenger Dlx Colour Television Receiver
Models:3634R,5134R,5443-R
For entering into Service Mode:
· Short contacts of the hidden SERVICE key inside the remote handset.
· After getting the screen of “SERVICES” press desired numeric key (“0”, “1”, “2”, “3”, “4”, “5”, “6”) to go into that menu.
· To enter into Service Mode, press numeric button “1”
· To enter into Design Mode, press numeric button “2”
· To enter Factory Shipping Mode, Press numeric button “3”
· To enter into Manufacturing Mode press numeric button “4”
· To access any parameter, use Up/Dn Keys of Program /Channel
· To change value of any parameter, use +/- keys of volume
· To exit, again short contacts of hidden Service Key or switch off the set into standby
SANSUI/VIDEOCON Colour Television Receiver
Models: SV-2012,SV-1412/5136-R
For entering into Service Mode:
· Short contacts of the hidden SERVICE key Inside the remote handset
             “TEST” will appear on the screen.
· Now, Press numeric keys ( “1”, “2”, “3”, “4”, “5”, “6”, “7”, “8”, “9” & “0” ) on the remote handset to get the various service menus.
· Note that menu no. 3,4 & 5 are general menus while menu no.1,2,6,7,8,9 & 0 are special menus. To access these menu enter special code “991220” when “TEST” appears on the screen.
· To access any parameter , use Up/Dn keys of Program/Channel
· To change value of any Parameter, use +/- keys of Volume
· To exit , again short contacts of hidden Service key or switch off the set into Standby
PHILIPS UOC Kit 

 For entering into Service Mode:
· First Press ‘MENU’ button and numeric  key “1147”on the remote handset to get the various service menus.
· To access any parameter , use Up/Dn keys of Program/Channel
· To change value of any Parameter, use +/- keys of Volume
TCL Colour Television Receiver
Model:T2111A
· Simultaneously press “DISPLAY” button on remote handset and Volume- button on the front panel of television receiver for 6 to 8 seconds  to get the various service menus.
· To access any parameter , use Up/Dn keys of Program/Channel
· To change value of any Parameter, use +/- keys of Volume
· To exit POWER switch off the set
 

Tuesday, June 21, 2011

അള്‍ട്രാ സോണിക് ഡിറ്റ്‌ക്ടര്‍

Ultrasonic Detector

സ്മാര്‍ട്ട് വാട്ടര്‍ പമ്പ്‌ സ്വിച്ചെര്‍

Smart Water Pump Switcher

ഈ ഗാര്‍ഡ്

E-Guard

ബൈക്കിനു ബാറ്ററി വേണ്ട

ബൈക്കിനു ബാറ്ററി വേണ്ട 



നമ്മുടെ ബൈക്കുകള്‍ ക്കെല്ലാം ബാറ്ററി ഉണ്ട് .ഈ ബാറ്ററി ബൈക്കില്‍ ഇല്ലെങ്കില്‍ എന്ത് സംഭവിക്കും ഒന്നും സംഭവിക്കില്ല ബാറ്ററി ക്ക് പകരക്കാരനായി നമ്മള്‍ ഒരു കപ്പാസിറ്റര്‍ ഖടിപ്പിക്കണമെന്നു മാത്രം .അതെങ്ങനെയെന്നു ഇനിപ്പറയാം.ആദ്യമായി ബൈക്കിലെ ബാറ്ററി ഊരിമാറ്റുക
എന്നിട്ട് അതെ സ്ഥാനത്ത് ഒരു 4700 MFD 25 വോള്‍ട്ട് കപ്പാസിറ്റര്‍ ഖടിപ്പിക്കുക  സോള്‍ടെര്‍ ചെയ്തു പിടിപ്പിക്കണം ഇല്ലെങ്കില്‍ ലൂസ്‌കോണ്ടാക്ട് ഉണ്ടാകാന്‍ സാധ്യത ഉണ്ട് .ഇനി വണ്ടി സ്റാര്‍ട്ട്  ചെയ്തു നോക്കൂ .ഇതിനു ചെറിയ രണ്ടു പോരായ്മകള്‍ ഉണ്ട് ,ഒന്ന്  സെല്‍ഫു സ്റാര്‍ട്ട്  ഉള്ള വണ്ടികള്‍ക്ക്  പുഷ് സ്റാര്‍ട്ട്  നടക്കില്ല ,രണ്ടു ബ്രേക്ക് ചവിട്ടുമ്പോള്‍ ഹോണിന്റെ  ശബ്ദം കുറയും .രണ്ടാമത്തെ പോരായ്മ പരിഹരിക്കാന്‍ ബ്രേക്ക് ലൈറ്റ്  ബള്‍ബു മാറ്റി  ഹൈ ബ്രൈറ്റ് LED  കള്‍ ഫിറ്റു ചെയ്‌താല്‍ മതി .രണ്ടു ഗുണങ്ങളും ഉണ്ട് ,ഒന്ന് മൈലേജു  കൂടും രണ്ടു എഞ്ചിന്‍ പുള്ളിംഗ് അല്‍പ്പം കൂടും .മൈലേജു കൂടാന്‍ കാരണം ബൈക്കിന്റെ ബാറ്ററി ഓട്ടത്തില്‍ നല്ല ഒരു ലോഡ് ആയാണ് പ്രവര്‍ത്തിക്കുന്നത്  ഇതോഴിവാകുമ്പോള്‍ അത്രയും എഞ്ചിന്‍ പവര്‍ ചക്രങ്ങള്‍ക്ക് കിട്ടുന്നു
മിക്കവാറും ബൈക്കുകളുടെ ബാറ്ററി രണ്ടു വര്‍ഷത്തിലധികം ഈടു നില്‍ക്കാറില്ല .ഇത് മാറ്റാന്‍ ചുരുങ്ങിയത് 800 രൂപയെങ്കിലും മുടക്കണം ഇനി ബാറ്ററി മാറ്റേണ്ടി വരുമ്പോള്‍ ഈ വിദ്യ പരീക്ഷിക്കൂ 
Photobucket
Photobucket
എനിക്ക്   5  മുതല്‍ 8  വരെ km  മൈലേജു കൂടി  കിട്ടുന്നുണ്ട്
ഈ ലേഖനം എഴുതിയത്  വറുഗീസ് ഗാര്‍ഡിയന്‍

Friday, June 17, 2011

ഏറണാകുളത്തെ ഊടുവഴികള്‍

    ഏറണാകുളത്തെ  ഊടുവഴികള്‍ 
ട്രാഫിക് ബ്ലോക്കുകളില്‍ പെടാതെ ഏറണാകുളം നഗരത്തില്‍ എവിടെയും എത്താന്‍ സഹായിക്കുന്ന പുസ്തകത്തിന്‍റെ ഓണ്‍ ലൈന്‍ പതിപ്പ് .നഗരത്തില്‍ വാഹനവുമായി എത്തുന്ന ഏവര്‍ക്കും ഉപകാര പ്രദം  ലഭിക്കുവാന്‍  താഴെക്കാണുന്ന  ചിത്രത്തില്‍ ക്ലിക്ക് ചെയ്യുക

Thursday, June 16, 2011

വിപണിയിലെ പുതുമ





വിപണിയിലെ പുതുമ

ദിനമെന്നോണം പുതിയ ഉല്‍പ്പന്നങ്ങള്‍ വിപണിയില്‍ എത്തുകയാണല്ലോ  അവയില്‍ ചിലതെല്ലാം പരിചയ പ്പെടുത്താനുള്ള ഒരെളിയ ശ്രമം

യൂനിവേര്‍സല്‍   മൊബൈല്‍  ബാറ്ററി ചാര്‍ജര്‍ വിത്ത് യൂ എസ് ബീ  പോര്‍ട്ട്‌ .
എല്ലാതരം മൊബൈല്‍ ഫോണ്‍ ബാറ്ററികളും ചാര്‍ജു ചെയ്യുവാന്‍ ഇതുപകരിക്കും
ഏകദേശ വില 65   രൂപ   ബ്രാന്‍ഡ്‌  /മേക്ക്   സ്പ്ളാഷ്


യൂനിവേര്‍സല്‍ പോര്‍ട്ട്‌ എഫ് .എം  റേഡിയോ
ഇതില്‍ മൊബൈല്‍ ഫോണില്‍ ഉപയോഗിക്കുന്ന മൈക്രോ എസ് ഡീ  കാര്‍ഡ് ,ക്യാമറയില്‍ ഉപയോഗിക്കുന്ന
എസ് ഡീ  കാര്‍ഡ്,പെന്‍ ഡ്രൈവ് ,എന്നിവയിലുള്ള മ്യൂസിക് ഫയലുകള്‍ play ചെയ്യാം .കൂടാതെ മൊബൈല്‍ ഫോണ്‍ ,എം പീ ത്രീ ,നെറ്റ്  ബുക്ക് എന്നിവയുടെ ആംപ്ലി ഫയര്‍ ആയും ഉപയോഗിക്കാം

റീ ചാര്‍ജബിള്‍ ബാറ്ററി ഉള്ളില്‍ അടങ്ങിയിട്ടുള്ള ഈ റേഡിയോ നോകിയ ടൈപ്പ്‌ ചാര്‍ജര്‍ ഉപയോഗിച്ച്  ചാര്‍ജു ചെയ്യാം
ഏകദേശ വില 325   രൂപ  

അള്‍ട്രാ ബ്രൈറ്റ് L E D ഹെഡ് ലൈറ്റ് 

 
ഇതിന്റെ പ്രകാശംനിങ്ങളെ വിസ്മയിപ്പിക്കും .റേഞ്ച് 500 മീറ്റര്‍.
 
റീ ചാര്‍ജബിള്‍ ബാറ്ററി ഉള്ളില്‍ അടങ്ങിയിട്ടുണ്ട്
.ഒറ്റ ചാര്‍ജില്‍ 300 മണിക്കൂര്‍ പ്രകാശിക്കും
ഏകദേശ വില 150  രൂപ   ബ്രാന്‍ഡ്‌  /മേക്ക്  ORKIA 

Monday, June 13, 2011

ലോ കോസ്റ്റ് ഹൈ സ്പീഡ് ഇന്‍റെര്‍നെറ്റ് ഓപ്പണ്‍ സിം

ലോ കോസ്റ്റ് ഹൈ സ്പീഡ് ഇന്‍റെര്‍നെറ്റ് ഓപ്പണ്‍ സിം
വലുതായി കാണുന്നതിന് ചിത്രത്തില്‍ ക്ലിക്ക് ചെയ്യുക
ഏറണാകുളത്തുള്ള ആന്‍കോണ്‍ മോബൈല്‍സ് എന്ന കമ്പനി ലോ കോസ്റ്റ് ഹൈ സ്പീഡ് ഓപ്പണ്‍ സിം ഇന്‍റെര്‍നെറ്റ് ഡിവൈസ് പുറത്തിറക്കിയിരിക്കുന്നു കൂടുതല്‍ വിവരങ്ങള്‍ക്ക് 9746474744 സതീഷ്‌ മാര്‍ക്കെറ്റിംഗ് മാനേജര്‍ ആന്‍കോണ്‍ മോബൈല്‍സ്


പ്രോജക്ടുകള്‍ക്ക് ആവശ്യമായ സോളാര്‍ പാനലുകളും മറ്റു കൊമ്പോനെന്റുകള്‍ക്കും ഫിറ്റ്‌ പാക്ക് ഇലക്ട്രോണിക്സ് കളമശ്ശേരി phone 0484 255578

മൊബൈല്‍ നമ്പര്‍ പോര്‍ട്ടബിലിറ്റി

മൊബൈല്‍ നമ്പര്‍ പോര്‍ട്ടബിലിറ്റി


















പഴയ മൊബൈല്‍ നമ്പര്‍ നിലനിര്‍ത്തികൊണ്ട് പുതിയ സേവനദാതാവിനെ(വോഡഫോണ്‍, എയര്‍ടെല്‍, ഐഡിയ, ബിഎസ്എന്‍എല്‍ തുടങ്ങിയ സേവനങ്ങള്‍) സ്വീകരിക്കുന്നതിനെയാണ് മൊബൈല്‍ നമ്പര്‍ പോര്‍ട്ടബിലിറ്റ് എന്നുപറയുന്നത്.
പഴയ മൊബൈല്‍ നമ്പര്‍ നിലനിര്‍ത്തികൊണ്ട് പുതിയ സേവനദാതാവിനെ സ്വീകരിക്കുന്നതിന് പോര്‍ട്ടിംഗ് എന്നുപറയും. പോര്‍ട്ടിംഗ് ചെയ്യണമെങ്കില്‍ നിലവിലുളള സേവനദാതാവില്‍നിന്ന് യുണീക് പോര്‍ട്ടിംഗ് കോഡ് (U.P.C) നേടേണ്ടതുണ്ട്.

PORT എന്ന് മൊബൈലില്‍ ടൈപ്പ് ചെയ്ത് അതിനു ശേഷം ഒരക്ഷരത്തിനുള്ള സ്ഥലം വിട്ട് (സ്‌പെയ്‌സ് നല്‍കി) നിലവിലുള്ള മൊബൈല്‍ നമ്പര്‍ ടൈപ്പ് ചെയ്ത് 1900 എന്ന നമ്പറിലേക്ക് എസ്എംഎസ് ചെയ്താല്‍ നിമിഷങ്ങള്‍ക്കകം 1901 എന്ന നമ്പറില്‍നിന്നു മറുപടിയായി യുപിസി ലഭിക്കും.

ഈ കോഡും നിങ്ങളുെട തിരിച്ചറിയല്‍ രേഖകളും പുതിയ കണക്ഷന് ആവശ്യമായ മറ്റു രേഖകളുമായി പോര്‍ട്ടിംഗ് സേവനം നല്‍കുന്ന ഡീലറെ സമീപിച്ചാല്‍ ദിവസങ്ങള്‍ക്കകം സേവനദാതാവിനെ മാറാന്‍ കഴിയും. പരമാവധി 19 രൂപയാണു പോര്‍ട്ടിംഗ് ചാര്‍ജ്.

പോര്‍ട്ടിംഗ് പ്രക്രിയ പൂര്‍ത്തീകരിക്കുംവരെ പഴയ കണക്ഷന്‍ ഉപയോഗിക്കാം. പോര്‍ട്ടിംഗ് പൂര്‍ത്തിയാക്കുന്ന തീയതിയും സമയവും എസ്എംഎസിലൂടെ അറിയിക്കും. പോര്‍ട്ടിംഗ് നടപടിയുടെ അവസാനഘട്ടത്തില്‍ രണ്ടു മണിക്കൂറുകള്‍ മൊബൈല്‍ ഫോണില്‍ വേസനം ലഭിക്കില്ല.

അര്‍ധരാത്രിക്കും പുലര്‍ച്ചെ അഞ്ചിനുമിടയിലായിരിക്കും ഈ നോ സര്‍വീസ് പീരിഡ്, അതിനാല്‍ ഉപയോക്താക്കള്‍ക്ക് കൂടുതല്‍ ബുദ്ധിമുട്ടുകള്‍ നേരിടേണ്ടിവരില്ല. ഈ സമയം കഴിയുമ്പോള്‍ പുതിയ സിംകാര്‍ഡ് ഉപയോഗിക്കാം. ഇതോടെ നമ്പര്‍ നിലനിര്‍ത്തിക്കൊണ്ട് പുതിയ ടെലികോം കമ്പനിയുടെ സേവനം ലഭിച്ചുതുടങ്ങും.

ഇതിനുള്ള വ്യവസ്ഥകള്‍

1. അപേക്ഷ നല്‍കി നാലു ദിവസത്തിനകം മാത്രമേ പോര്‍ട്ടിംഗ് നടക്കുകയുള്ളു

2 ഒരു തവണ പോര്‍ട്ടിംഗ് നടത്തിയാല്‍ അടുത്തത് 90 ദിവസം കഴിഞ്ഞുമാത്രം. (ആദ്യ പോര്‍ട്ടിംഗാണെങ്കില്‍ കണക്ഷന്‍ പ്രവര്‍ത്തനക്ഷമമായി 90 ദിവസം കഴിയണം)

3 പ്രീപെയ്ഡ് കണക്ഷനില്‍ പോര്‍ട്ടിംഗ് സമയത്തുള്ള ബാലന്‍സ് ടോക്‌ടൈം നഷ്ടമാകും.

4 ഒരു ടെലികോം സര്‍ക്കിളിനുള്ളില്‍ മാത്രമേ പോര്‍ട്ടിംഗ് നടത്താന്‍ കഴിയൂ.

5. പോസ്റ്റ് പെയ്ഡ് കണക്ഷനില്‍ ബില്‍ കുടിശിക ഉണ്ടെങ്കില്‍ പോര്‍ട്ടിംഗ് അനുവദിക്കില്ല. (നിലവിലുള്ള സേവനദാതാവിന്റെ ക്ലിയറന്‍സ് കിട്ടിയാല്‍ മാത്രമേ പോര്‍ട്ടിംഗ് നടക്കൂ)

6 .പോര്‍ട്ടിംഗ് ചാര്‍ജ് 19 രൂപയില്‍ കൂടാന്‍ പാടില്ല